Ohm's Law — Voltage, Current & Resistance
The fundamental relationship that governs every electric circuit
Voltage — the pressure that pushes current
Voltage (V) is the electrical potential difference between two points — the "push" that drives charges around a circuit. A battery creates voltage by maintaining a chemical energy difference between its terminals. The higher the voltage, the more energy each coulomb of charge carries.
Current — charges in motion
Current (I) is the rate at which electric charge flows past a point, measured in amperes (A). One ampere equals one coulomb per second. In a wire, billions of electrons drift slowly (mm/s) but the electric signal propagates at nearly the speed of light.
Resistance — opposition to flow
Resistance (R) is a material's opposition to current flow, measured in ohms (Ω). A thin wire, a poor conductor, or a long wire all have higher resistance. Resistance converts electrical energy to heat — the basis of resistors, heating elements, and filament bulbs.
Ohm's Law: V = I × R
Ohm's Law states that for a resistor, voltage equals current times resistance: V = IR. Double the voltage and the current doubles. Double the resistance and current halves. This linear relationship is the cornerstone of circuit analysis — use it to find any one quantity when the other two are known: I = V/R and R = V/I.
Power dissipation — where the energy goes
Every resistor converts electrical energy into heat. The power dissipated is P = I × V, which (using Ohm's Law) can also be written as P = I²R or P = V²/R. Watch the resistor glow brighter as power increases — that glow represents real thermal energy. A 60 W light bulb, a 1 000 W heater, and a tiny 0.25 W resistor all follow this same equation. Understanding power is critical for choosing components that won't overheat.
Reading the I–V graph
Inside the circuit loop, the canvas plots current I (up) against voltage V (across) from 0 to 24 V, and the dot marks the present setting. For a resistor every point lies on one straight line through the origin whose slope is 1/R — move the 'Resistance' slider down and the line gets steeper. A straight line through the origin is exactly what obeying Ohm's Law means.
Non-ohmic components — the filament bulb
Choose 'Filament bulb (non-ohmic)' in the Component menu. A filament gets hotter as more voltage is applied, and hot metal resists current more, so its resistance is not fixed. The canvas uses a simplified model: R_hot = R_cold × (1 + V / 6 V). Slide the voltage up and watch the graph bend below the dashed straight line of a resistor with the same cold value.
Worked Example: resistor versus bulb at 12 V
Set Voltage to 12 V and Resistance to 3 Ω. The resistor passes I = 12 / 3 = 4 A and dissipates 48 W. Now switch to the bulb: its resistance rises to 3 × (1 + 12 / 6) = 9 Ω, so only I = 12 / 9 ≈ 1.33 A flows and it dissipates about 16 W. V = IR still links the three numbers at that moment — what changed is R itself.
How It Works — Step by Step
-
1
Voltage — the pressure that pushes current
Voltage (V) is the electrical potential difference between two points — the "push" that drives charges around a circuit. A battery creates voltage by maintaining a chemical energy difference between its terminals. The higher the voltage, the more energy each coulomb of charge carries.
-
2
Current — charges in motion
Current (I) is the rate at which electric charge flows past a point, measured in amperes (A). One ampere equals one coulomb per second. In a wire, billions of electrons drift slowly (mm/s) but the electric signal propagates at nearly the speed of light.
-
3
Resistance — opposition to flow
Resistance (R) is a material's opposition to current flow, measured in ohms (Ω). A thin wire, a poor conductor, or a long wire all have higher resistance. Resistance converts electrical energy to heat — the basis of resistors, heating elements, and filament bulbs.
-
4
Ohm's Law: V = I × R
Ohm's Law states that for a resistor, voltage equals current times resistance: V = IR. Double the voltage and the current doubles. Double the resistance and current halves. This linear relationship is the cornerstone of circuit analysis — use it to find any one quantity when the other two are known: I = V/R and R = V/I.
-
5
Power dissipation — where the energy goes
Every resistor converts electrical energy into heat. The power dissipated is P = I × V, which (using Ohm's Law) can also be written as P = I²R or P = V²/R. Watch the resistor glow brighter as power increases — that glow represents real thermal energy. A 60 W light bulb, a 1 000 W heater, and a tiny 0.25 W resistor all follow this same equation. Understanding power is critical for choosing components that won't overheat.
-
6
Reading the I–V graph
Inside the circuit loop, the canvas plots current I (up) against voltage V (across) from 0 to 24 V, and the dot marks the present setting. For a resistor every point lies on one straight line through the origin whose slope is 1/R — move the 'Resistance' slider down and the line gets steeper. A straight line through the origin is exactly what obeying Ohm's Law means.
-
7
Non-ohmic components — the filament bulb
Choose 'Filament bulb (non-ohmic)' in the Component menu. A filament gets hotter as more voltage is applied, and hot metal resists current more, so its resistance is not fixed. The canvas uses a simplified model: R_hot = R_cold × (1 + V / 6 V). Slide the voltage up and watch the graph bend below the dashed straight line of a resistor with the same cold value.
-
8
Worked Example: resistor versus bulb at 12 V
Set Voltage to 12 V and Resistance to 3 Ω. The resistor passes I = 12 / 3 = 4 A and dissipates 48 W. Now switch to the bulb: its resistance rises to 3 × (1 + 12 / 6) = 9 Ω, so only I = 12 / 9 ≈ 1.33 A flows and it dissipates about 16 W. V = IR still links the three numbers at that moment — what changed is R itself.
Key Takeaways
V = IR is the most useful equation in electronics
Every circuit calculation starts with V = IR. Once you understand it, you can analyse series circuits, parallel circuits, voltage dividers, and power dissipation (P = IV = I²R = V²/R).
Ohm's Law has limits
Ohm's Law applies to resistors (and most conductors at constant temperature): their I–V graph is a straight line through the origin. It does NOT apply to diodes, transistors, or filament bulbs, whose resistance changes as the current heats them — their I–V graph curves.
Safety comes from understanding
Household circuits are ~230 V. Even 100 mA through the heart can be fatal. Fuses and circuit breakers exploit Ohm's Law — they break the circuit before current reaches dangerous levels.
Connected Concepts
Electric Field
Voltage is the potential energy difference created by electric fields — it drives current around a circuit.
Waves
AC circuits carry alternating current — voltage and current oscillate as sine waves at the supply frequency.
Semiconductors
A diode's curved I–V graph is exactly what a component that does NOT obey V = IR looks like.
Electric Circuits
Series and parallel circuits are Ohm's Law applied again and again — every branch and every resistor obeys V = IR.
Kirchhoff's Laws
Combine V = IR for each component with the current and voltage rules to solve circuits with several loops.
RLC Circuits & Resonance
V = IR still applies to the resistor in an RLC circuit at every instant — it just now shares the circuit with two components whose opposition to current depends on frequency.
The Water-Pipe Analogy
Pump pressure plays voltage, water flow plays current and a narrow pipe plays a resistor, so flow = pressure ÷ narrowness mirrors I = V ÷ R.
Updated
- — New connection to The Water-Pipe Analogy.
- — New live I–V graph, a filament-bulb mode that shows a non-ohmic component, two bulb challenges and a worked example